Our oil is a natural product. Hemp is a plant, and no two harvests are exactly the same. That is why every batch differs slightly in composition, colour and taste. We see no problem in that, but we do want you to know exactly what you are buying. That is why we have every batch analysed independently and share the results here.
How we make our oil
We use a crude full spectrum hemp extract (crude oil). This extract is not refined or filtered down to a single compound, so it contains the natural mix of the plant:
- CBD and a wide range of other (minor) cannabinoids
- terpenes, which give aroma and taste
- flavonoids
- natural plant waxes
We blend this crude extract with MCT oil to the strength on the label: 5%, 10%, 20% or 30%. Because the extract is unrefined, the oil has a dark colour and a herbal, slightly bitter taste. That is normal for a full spectrum product.
Analysis of the current batch
| Batch number | CBD-CRU-260331 | |
| Date of analysis | 24 March 2026 | |
| Analytical method | UPLC–PDA (UV) | |
| Laboratory | Independent laboratory in the EU, accredited by the European Medicines Agency (EMA) and analytically GMP certified | |
| Measured in | the crude extract, before dilution with MCT oil | |
| Cannabinoid | Abbreviation | Content |
|---|---|---|
| Cannabidiol | CBD | 61,14% |
| Cannabicitran | CBT | 2,25% |
| Cannabigerol | CBG | 1,36% |
| Cannabinol | CBN | 0,88% |
| Cannabichromene | CBC | 0,72% |
| Cannabidivarin | CBDV | 0,63% |
| Delta-9-tetrahydrocannabinol | Δ9-THC | 0,37% |
| Cannabidibutol | CBDB | 0,17% |
| Cannabicyclol | CBL | 0,10% |
| Total THC | Σ THC | 0,37% |
Not detectable (below the limit of quantitation of 0.05%): CBDA, CBDVA, CBGA, THCA, CBCA, CBLA and Δ8-THC.
In total, 9 different cannabinoids were measured in this batch, together about 67.6% of the extract. All values are in weight percent (w/w) of the crude extract.
Note on THC: the report above shows 0.37% total THC. An additional measurement of the THC content in the crude extract gave 0.12% THC at about 60% CBD. We use that value below for the calculation per strength.
What does this mean for your bottle?
The percentages above apply to the pure, crude extract. In our oil this extract is diluted with MCT oil. The CBD content in the bottle is the strength on the label (5%, 10%, 20% or 30%). All other compounds, including THC, are diluted in the same ratio and are therefore much lower in the oil than in the table.
THC per strength
| Strength (CBD) | THC in the oil (calculated) |
|---|---|
| 5% | approx. 0.01% |
| 10% | approx. 0.02% |
| 20% | approx. 0.04% |
| 30% | approx. 0.06% |
Calculated from an additional THC measurement of the crude extract: 0.12% THC at about 60% CBD, diluted with MCT oil to the strength on the label. Every batch is different. Check the rules on THC in your own country.
Why does every batch differ?
The composition of hemp depends on the variety, the weather, the soil and the time of harvest. As a result, the content of CBG, CBN or terpenes, for example, can differ slightly per batch. The strength on the label stays the same, but the ratio between the minor cannabinoids, the colour and the taste can vary per batch.
Transparency
- We have every batch tested by an independent laboratory.
- We publish the results of the current batch on this page, including the batch number and date of analysis.
- When a new batch arrives, we replace this data with the new analysis.
- To protect our supply chain we do not show the names of suppliers or the laboratory. The measurement results themselves are taken unchanged from the report.
- Questions about the analysis? Contact us.
Our products are not medicines and are not intended to diagnose, treat, cure or prevent any disease. For adults (18+) only.